Ways To Punch A Hole In A Leather Belt

Bring alongside your belt when procuring, to compare the size of the punch with the scale of the prevailing holes. I came across this Reddit information awhile in the past and was inspired to make my very own pure coloration Leather belt. I've all the time loved Tanner Goods natural belt with black buckle however would never be capable of justify spending $88 on a belt. That is to not say Tanner doesn't make amazing stuff, I'm just not the kind of man that spends an affordable meal shy of a hundred bucks on one belt. The entire objects you will need ought to be accessible regionally at a Leather items retailer or passion store.
Use a ruler or measuring tape to seek out the distance between each Hole, then measure the same distance past the final Hole. Use heavy objects to keep the belt taut, or have a friend pull the belt taut in entrance of you. Some thick belts could require strong hands, or someone to wiggle the taut belt back and forth as you squeeze. Use a ruler to measure the spacing between the opening, then measure the identical distance previous the last Hole.



Work slowly and carefully-this top sew will maintain your belt together, but it should also look superbly decorated if it's carried out properly! Start on the bottom corner of the tail end (the place you possibly can see I left the threads on the left aspect), go down the tip, and then pivot on the nook to turn and continue all the best way down the length of your belt. It shouldn't take much thread, but be further careful for those who're working with a thicker cloth.
If the new spot is not exactly on a measured place, create a Hole barely beyond that point. After checking the dots another time for accuracy, place the belt in the Leather punch instrument. Lining up the slicing point and the outlet, clamp down on the tool as onerous as attainable to punch the hole. After slicing the holes, brush off the surplus Leather and check out the belt on for size. Make sure that the holes are giant enough that the buckle prong can fit by fully. Safe the belt to the desk and place one thing underneath the belt first to guard the end.

You must ensure the unit is designed to line up appropriately with the slicing plate as a result of every cut I needed to test it by lining it up and taking a look at it with mild behind it to see if it could hit flat and even then I did not get an excellent lower. The first time I needed further holes for my belt I laid the belt on our eating table, took a steak knife, stabbed and began twisting the knife into the Leather as if I used to be trying to make a boy scout fireplace with two sticks of wood.
Work slowly and thoroughly-this prime stitch will keep your belt together, but it'll also look beautifully decorated if it is performed effectively! Start on the bottom corner of the tail finish (where you can see I left the threads on the left aspect), go down the top, and then pivot at the corner to show and continue all the best way down the length of your belt. It should not take much thread, however be further cautious if you happen to're working with a thicker fabric.
I warmth the nail over the range, drive it with pliers, bend the belt on the outlet and smoothen edges with sand paper. Sadly, if you put a lot strain on it, the uneven Hole will permit the Leather to tear quite easily. Lay the belt down on a flat surface, fallacious aspect up. Measure how far apart the pre-lower belt holes are in an effort to place the brand new belt holes appropriately. For the sake of aesthetics, you need to put in holes as much as the purpose of the desired closure level.

You need to attempt on the belt and get an concept for how a lot you have to to convey the belt in, one extra Hole is all i wanted for this one. Some belts have screws near make hole in belt the buckle which you can take away and relocate to shrink the belt. I don't have a Leather Hole punch, so I simply used a nail that I had and punched the outlet a couple of times.
It should be thinner than the width you used to your belt and lengthy enough to wrap across the width of your belt with a little additional to overlap with. Measure about 1.5″ in. on the top of the squared tail finish of your belt and mark this spot within the center of the belt's width and then use your grommet Hole cutter to punch a Hole into the spot you marked. Besides, a few of them generally is a little awful on the the precise belt part at occasions.

Leave a Reply

Your email address will not be published. Required fields are marked *